I am putting here instructions for 25004. I do not look here very often, so let it be here. But the drawings were not included. I think this is not critical.
MULTI COOKER 25004
SECURITY MEASURES
Important safety instructions. Read carefully and keep for future reference. Improper handling of the device can damage it and harm the user. Before using for the first time, check that the technical specifications of the product indicated on the decal correspond to those of the mains supply.
ATTENTION! The power cord plug has a grounding wire and a grounding prong. Connect the appliance only to a suitable grounded socket.
Use only for domestic purposes in accordance with this Instruction Manual. The device is not intended for industrial use.
Do not use outdoors.
Always unplug the device from the mains before cleaning or when not in use. The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience or knowledge, unless they are supervised or instructed to use the appliance by a person responsible for their safety.
Children must be supervised to ensure that they do not play with the appliance.
Do not leave the switched on device unattended.
Do not use accessories not supplied.
Do not use the device with a damaged power cord and / or plug. To avoid a hazard, a damaged power cord must be replaced by an authorized service center. Do not immerse the device and power cord in water or other liquids. If this happens, immediately disconnect the device from the mains and, before using it further, check the functionality and safety of the device by qualified specialists. Keep the power cord away from sharp edges and hot surfaces. Do not pull, twist, or wind the power cord around the device. Use the multicooker only for cooking food. Never dry clothes, paper, or other items in it.
Do not turn on the multicooker with an empty pan. Do not use a multicooker without a pan.
The appliance is not intended for preserving food. Do not place food directly on the bottom of the multicooker, use a saucepan.
Do not replace the pan with another container. Do not use metal objects that could scratch the pot. The coating applied to the surface of the pot may wear off gradually, so use it with care. Follow the cooking recipes. To avoid short circuits and damage to the device, do not allow water to enter the ventilation openings.
Inadequate maintenance of the multicooker in a clean condition leads to surface wear, which can adversely affect the operation of the appliance and create a possible danger to the user. When using an extension cord, make sure that the maximum power rating of the cable matches the power rating of the appliance.
Attention! The device heats up during operation! If you need to contact the multicooker during its operation, use oven mitts or oven mitts.
Protect your face and hands from steam escaping from the valve. Do not insert metal or other objects into the outlet or any other part of the product.
Do not cover the lid of the multicooker with towels or other items.
COOKING DELAY FUNCTION
This function allows you to delay the cooking process for a time from 30 minutes to 24 hours. Place all ingredients and seasonings in the multicooker saucepan as per recipe.
Place the pot in a multicooker. Close the cover until you hear a click. The click will be slight.
Connect the multicooker to the mains. Do not connect the appliance to the mains until all preparations have been completed - this can lead to damage. The display will show "0000".
Press the "Time setting" button, the display will show "00:30" (delay of cooking time 30 minutes), each time you press this button, the time will increase by 30 minutes), one press: "0:30" (30 minutes), two pressing: "1:00" (1 hour), three pressing: "1:30" (1 hour 30 minutes), then you press the button of the program that you plan to cook. For example "Potato". Based on the cooking program, follow all the steps of the instructions described above. When the program entry is complete, the delay time will be displayed on the multicooker screen and the time will start counting down.
SPECIAL ATTENTION: The cooking time that is shown on the display when choosing a program is the cooking time of the product after the required temperature and pressure in the multicooker has been set.
To activate the timer for the delayed start of cooking, press the "Time setting" button. The maximum delayed start time for cooking is 24 hours, after setting the time, the device will start heating only after the time you have set has elapsed. If you opened the multicooker and saw that the product is not completely ready, repeat the cooking process again, this situation may arise if you initially put a large amount of the product for cooking.
Always set the overpressure valve to the "AIRPROOF" position before starting work. Never touch the cover and the pressure release valve while the unit is operating. This could result in burns. After selecting a function, work will begin.
Do not put your hands on the air valve when the appliance is in operation to avoid scalding when steam comes out. Please put the multicooker out of the reach of children. Rough handling can result in fire, electric shock, or property damage.
Never plug in the appliance before locking the cover.
Nothing should be on the overpressure valve.
SELECTION OF PARAMETERS: Select one of the seven functions: "Rice / Porridge", "Soup", "Braising", "Meat", "Potatoes", "Chicken", "Steaming" the multicooker will heat up, on the display when heating you will see the following indication "----" heating mode. After reaching the optimal temperature, you will see the cooking time on the display, during the cooking process, the time on the display will periodically decrease according to the set program and the multicooker will switch to heating mode, accompanied by the readings “----“ on the display.
PROGRAM "RICE \ PORSE" This mode is used for cooking various types of cereals, pilaf. Measure out the grits with a measuring spoon. If necessary, the cereals should be pre-rinsed. Do not use the multicooker pan for these purposes, you may damage its coating. Pour the cereal into the multicooker saucepan. Pour water into a saucepan.Place the pot in a multicooker. Close the cover until you hear a click (fig. 1). Close the manual pressure release valve, put it in the “AIRPROOF” mode - closed position (Fig. 2).
fig. 1 fig. 2
Connect the multicooker to the mains. Do not connect the appliance to the mains until all preparations have been completed - this can lead to damage. Press the "Rice / Porridge" button on the control panel. The display will show PP20 - this is a cooking time of 20 minutes. The Rice / Porridge program will start. After the end of the cooking time, a short sound signal will sound and the multicooker will switch to the “Heating” mode, the display will show “66” to keep the product hot.
If you need to remove the food immediately after cooking, follow these steps:
-after a short beep sounds, the multicooker will switch to heating mode, turn off this mode using the "Heating off" button;
- let the multicooker cool down to cool it faster, cover it with a damp towel without closing the steam release valve;
- carefully switch the forced steam release valve to the "EXHAUST" position, open position, this action will release the multicooker from the remaining steam that was formed during cooking;
-turn the lid very carefully and open the multicooker.
ATTENTION: during heating mode, the countdown is not shown on the display; during heating, you see the image "----" on the display.
The heating time depends on the volume and weight of the product loaded into the multicooker.
After the end of the program, a sound signal will sound and the multicooker will switch to the "Heating" heating mode to turn off the heating, press the "Heating off" button. If there is not enough time for the dish to be ready, you need to turn it on again after turning off the program and set the required time.
SOUP PROGRAM This mode is used for making soups. Place all ingredients and seasonings in a multicooker saucepan. Place the pot in a multicooker. Close the cover until you hear a click (fig. 1). Close the manual pressure release valve, put it in the “AIRPROOF” mode - closed position (Fig. 2).
fig. 1 fig. 2
Connect the multicooker to the mains. Do not connect the appliance to the mains until all preparations have been completed - this can lead to damage. Press the "Soup, borscht" button on the control panel. The display will show PP25 - this is a cooking time of 25 minutes. The Borsch Soup program will start working. After the end of the cooking time, a short sound signal will sound and the multicooker will switch to the “Heating” mode, the display will show “66” to keep the product hot. If you need to remove the food immediately after cooking, follow these steps:
-after a short beep sounds, the multicooker will switch to heating mode, turn off this mode using the "Heating off" button;
- let the multicooker cool down, in order to cool it faster, cover it with a damp towel without closing the steam release valve;
- carefully switch the forced steam release valve to the "EXHAUST" position, open position, this action will release the multicooker from the remaining steam that was formed during cooking;
-turn the lid very carefully and open the multicooker.
ATTENTION: during heating mode, the countdown is not shown on the display, during heating, you see the image "----" on the display.
The heating time depends on the volume and weight of the product loaded into the multicooker.
After the end of the program, a sound signal will sound and the multicooker will switch to the “Heating” heating mode. To turn off the heating, press the “Heating off” button. If there is not enough time for the dish to be ready, you need to turn it on again after turning off the program and set the required time.
EXTINGUISHING PROGRAM This mode is used to extinguish food. Place all ingredients and seasonings in the saucepan of your multicooker. Place the pot in a multicooker.Close the cover until you hear a click (fig. 1). Close the manual pressure release valve, put it in the “AIRPROOF” mode - closed position (Fig. 2).
fig. 1 fig. 2
Connect the multicooker to the mains. Do not connect the appliance to the mains until all preparations have been completed - this may lead to damage. Press the Extinguish button on the control panel. The display will show PP30 - this is a cooking time of 30 minutes. The Extinguishing program will start working. After the end of the cooking time, a short beep will sound and the multicooker switches to the "Heating" mode, the display shows "66" to keep the product hot. If you need to remove the food immediately after cooking, follow these steps:
-after a short beep sounds, the multicooker will switch to heating mode, turn off this mode using the "Heating off" button;
- let the multicooker cool down to cool it faster, cover it with a damp towel without closing the steam release valve;
- carefully switch the forced steam release valve to the "EXHAUST" position open, this action will release the multicooker from the remaining steam that was formed during cooking;
-turn the lid very carefully and open the multicooker.
ATTENTION: during heating mode, the countdown is not shown on the display; during heating, you see the image "----" on the display.
The heating time depends on the volume and weight of the product loaded into the multicooker.
After the end of the program, a sound signal will sound and the multicooker will switch to the “Heating” heating mode. To turn off the heating, press the “Heating off” button. If there is not enough time for the dish to be ready, you need to re-enable and set the required time after turning off the program.
PROGRAM "MEAT" This mode is used for cooking meat dishes. Place all ingredients and seasonings in the saucepan of your multicooker. Place the pot in a multicooker. Close the cover until you hear a click (fig. 1). Close the manual pressure release valve, put it in the “AIRPROOF” mode - closed position (Fig. 2).
fig. 1 fig. 2
Connect the multicooker to the mains. Do not connect the appliance to the mains until all preparations have been completed - this may lead to damage. Press the Meat button on the control panel. The display will show PP06 - this is a cooking time of 6 minutes. The Meat program will start working. After the end of the cooking time, a short beep will sound and the multicooker switches to the "Heating" mode, the display shows "66" to keep the product hot. If you need to remove the food immediately after cooking, follow these steps:
-after a short beep sounds, the multicooker will switch to heating mode, turn off this mode using the "Heating off" button;
- let the multicooker cool down to cool it faster, cover it with a damp towel without closing the steam release valve;
- carefully switch the forced steam release valve to the "EXHAUST" position open, this action will release the multicooker from the remaining steam that was formed during cooking;
-turn the lid very carefully and open the multicooker.
ATTENTION: during heating mode, the countdown is not shown on the display; during heating, you see the image "----" on the display.
The heating time depends on the volume and weight of the product loaded into the multicooker.
After the end of the program, a sound signal will sound and the multicooker will switch to the “Heating” heating mode. To turn off the heating, press the “Heating off” button. If there is not enough time for the dish to be ready, you need to re-enable and set the required time after turning off the program.
POTATO PROGRAM This mode is used for cooking potatoes. Place all ingredients and seasonings in the saucepan of your multicooker. Place the pot in a multicooker.
Close the cover until you hear a click (fig. 1).Close the manual pressure release valve, put it in the “AIRPROOF” mode - closed position (Fig. 2).
fig. 1 fig. 2
Connect the multicooker to the mains. Do not connect the appliance to the mains until all preparations have been completed - this may lead to damage. Press the Potatoes button on the control panel. The display will show PP10 - this is a cooking time of 10 minutes. The Potato program will start working. After the end of the cooking time, a short beep will sound and the multicooker switches to the "Heating" mode, the display shows "66" to keep the product hot. If you need to remove the food immediately after cooking, follow these steps:
-after a short beep sounds, the multicooker will switch to heating mode, turn off this mode using the "Heating off" button;
- let the multicooker cool down to cool it faster, cover it with a damp towel without closing the steam release valve;
- carefully switch the forced steam release valve to the "EXHAUST" position open, this action will release the multicooker from the remaining steam that was formed during cooking;
-turn the lid very carefully and open the multicooker.
ATTENTION: during heating mode, the countdown is not shown on the display; during heating, you see the image "----" on the display.
The heating time depends on the volume and weight of the product loaded into the multicooker.
After the end of the program, a sound signal will sound and the multicooker will switch to the "Heating" heating mode. To turn off the heating, press the "Turn off the heating" button. If there is not enough time for the dish to be ready, you need to re-enable and set the required time after turning off the program.
STEAM PROGRAM This mode is used to steam food. The "Steaming / Steam cooking" mode is used with the use of a container-steamer. It is important to know that steam cooking time is limited by the amount of water poured into the pot. Pour in enough water to cover the entire cooking process. Place the pot in a multicooker.
Close the cover until you hear a click (fig. 1). Close the manual pressure release valve, put it in the “AIRPROOF” mode - closed position (Fig. 2).
fig. 1 fig. 2
Connect the multicooker to the mains. Do not connect the appliance to the mains until all preparations have been completed - this may lead to damage. Press the "Steam" button on the control panel. The display will show PP15 - this is a cooking time of 15 minutes. The "Steam cooking" program will start. After the end of the cooking time, a short sound signal will sound and the multicooker switches to the “Heating” mode to keep the product hot, the display will show “66”. If you need to remove the food immediately after cooking, follow these steps:
-after a short beep sounds, the multicooker will switch to heating mode, turn off this mode using the "Heating off" button;
- let the multicooker cool down to cool it faster, cover it with a damp towel without closing the steam release valve;
- carefully switch the forced steam release valve to the "EXHAUST" position open, this action will release the multicooker from the remaining steam that was formed during cooking;
-turn the lid very carefully and open the multicooker.
ATTENTION: during heating mode, the countdown is not shown on the display; during heating, you see the image "----" on the display.
The heating time depends on the volume and weight of the product loaded into the multicooker.
After the end of the program, a sound signal will sound and the multicooker will switch to the "Heating" heating mode. To turn off the heating, press the "Turn off the heating" button. If there is not enough time for the dish to be ready, you need to re-enable and set the required time after turning off the program.
CLEANING: Unplug before cleaning.
Wipe the bottom of the multicooker with a sponge. Do not immerse the multicooker in water or pour water into it.
Take out the inner pot and wash it.
Use only a soft cloth or sponge to clean the inner pot.
SPECIFICATIONS
Power supply 220-240V ~, 50Hz
Power 900W
The manufacturer reserves the right to change any specifications without prior notice to the consumer.
For additional information or in case of any problems, please contact the service centers whose addresses are indicated in the warranty card.